U-Boot 1.1.1 (Nov 13 2006 – 14:01:34) Marvell version: 1.4.2

DRAM CS[0] base 0×00000000 size 64MB
DRAM Total size 64MB
[8192kB@ff800000] Flash: 8 MB
Addresses 20M – 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M – 16M): Done
*** Warning – bad CRC, using default environment

Soc: MV88F5181 Rev 3
CPU: ARM926 (Rev 0) running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz

Init usb device.
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Hit any key to stop autoboot: 3 2 1 0
## Booting image at ff820000 …
Image Name: Linux-2.6.12.6-arm1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1490204 Bytes = 1.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum … OK
OK
## Loading Ramdisk Image at ff9a0000 …
Image Name: Ramdisk
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5507627 Bytes = 5.3 MB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum … Bad Data CRC ** LOADER **
** MARVELL BOARD: RD-88F5181-POS-NAS LE

U-Boot 1.1.1 (Nov 13 2006 – 14:01:34) Marvell version: 1.4.2

DRAM CS[0] base 0×00000000 size 64MB
DRAM Total size 64MB
[8192kB@ff800000] Flash: 8 MB
Addresses 20M – 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M – 16M): Done
*** Warning – bad CRC, using default environment

Soc: MV88F5181 Rev 3
CPU: ARM926 (Rev 0) running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz

Init usb device.
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Hit any key to stop autoboot: 3 2 1 0
## Booting image at ff820000 …
Image Name: Linux-2.6.12.6-arm1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1490204 Bytes = 1.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum … OK
OK
## Loading Ramdisk Image at ff9a0000 …
Image Name: Ramdisk
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5507627 Bytes = 5.3 MB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum … Bad Data CRCя ** LOADER **
** MARVELL BOARD: RD-88F5181-POS-NAS LE

U-Boot 1.1.1 (Nov 13 2006 – 14:01:34) Marvell version: 1.4.2

DRAM CS[0] base 0×00000000 size 64MB
DRAM Total size 64MB
[8192kB@ff800000] Flash: 8 MB
Addresses 20M – 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M – 16M): Done
*** Warning – bad CRC, using default environment

Soc: MV88F5181 Rev 3
CPU: ARM926 (Rev 0) running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz

Init usb device.
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Hit any key to stop autoboot: 3 2 1 0
## Booting image at ff820000 …
Image Name: Linux-2.6.12.6-arm1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1490204 Bytes = 1.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum … OK
OK
## Loading Ramdisk Image at ff9a0000 …
Image Name: Ramdisk
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5507627 Bytes = 5.3 MB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum … Bad Data CRCя ** LOADER **
** MARVELL BOARD: RD-88F5181-POS-NAS LE

U-Boot 1.1.1 (Nov 13 2006 – 14:01:34) Marvell version: 1.4.2

Starting kernel …

U-Boot 1.1.1 (Feb 26 2009 – 11:33:03) Marvell version: 1.7.3.003

DRAM CS[0] base 0×00000000 size 64MB
DRAM Total size 64MB
Detect phy 1111
[8192kB@ff800000] Flash: 8 MB
Addresses 20M – 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M – 16M): Done
*** Warning – bad CRC, using default environment

Soc: MV88F5182 Rev 2
CPU: ARM926 (Rev 0) running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz

USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Hit any key to stop autoboot: 0
Marvell>> loadb
## Ready for binary (kermit) download to 0×00100000 at 115200 bps…
## Total Size = 0x0016bd5c = 1490268 Bytes
## Start Addr = 0×00100000
Un-Protect Flash Bank # 1
Kernel Size = 0
Copy to Flash… done
Protect Flash Bank # 1
Marvell>> cp 0100000 02000000 1490268
Marvell>> loadb
## Ready for binary (kermit) download to 0×00100000 at 115200 bps…
## Total Size = 0x00540a6b = 5507691 Bytes
## Start Addr = 0×00100000
Un-Protect Flash Bank # 1
Kernel Size = 0
Copy to Flash… done
Protect Flash Bank # 1
Marvell>> cp 0100000 03000000 5507691
Marvell>> bootm 02000000 03000000
## Booting image at 02000000 …
Image Name: Linux-2.6.12.6-arm1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1490204 Bytes = 1.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum … OK
OK
## Loading Ramdisk Image at 03000000 …
Image Name: Ramdisk
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5507627 Bytes = 5.3 MB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum … OK

Starting kernel …

Uncompressing Linux……………………………………………………………………………………… done, booting the kernel.
Linux version 2.6.12.6-arm1 (tim@SWTEST2) (gcc version 3.3.3) #47 Mon Nov 30 12:06:02 CST 2009
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 166000000, Tclk = 166000000
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none
PID hash table entries: 512 (order: 9, 8192 bytes)
Console: colour dummy device 80×30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB 0MB 0MB 0MB = 64MB total
Memory: 56192KB available (2599K code, 462K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs…it isn’t (no cpio magic); looks like an initrd
Freeing initrd memory: 5378K
NET: Registered protocol family 16

Marvell Development Board (LSP Version 1.7.6_NAS)– RD-88F5182-NAS-2

Detected Tclk 166000000 and SysClk 166000000
Marvell USB EHCI Host controller #0: c0d43b00
Marvell USB EHCI Host controller #1: c0d43a40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
cesadev_init(c0012468)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.3 (2007/10/31) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0×0 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver ‘egiga’:
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ‘egiga0′
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
physmap flash device: 800000 at ff800000
phys_mapped_flash: Found 1 x16 devices at 0×0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0×0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition definition
Creating 5 MTD partitions on “phys_mapped_flash”:
0×00000000-0×00010000 : “MTD1″
0×00010000-0×00020000 : “MTD2″
0×00020000-0x001a0000 : “Linux Kernel”
0x001a0000-0x007d0000 : “File System”
0x007d0000-0×00800000 : “u-boot”
ehci_platform ehci_platform.20865: EHCI Host Controller
ehci_platform ehci_platform.20865: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.20865: irq 17, io mem 0×00000000
ehci_platform ehci_platform.20865: park 0
ehci_platform ehci_platform.20865: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.86401: EHCI Host Controller
ehci_platform ehci_platform.86401: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.86401: irq 12, io mem 0×00000000
ehci_platform ehci_platform.86401: park 0
ehci_platform ehci_platform.86401: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mice: PS/2 mouse device common for all mice
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun …
md: … autorun DONE.
RAMDISK: Compressed image found at block 0
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 112K
init started: BusyBox v1.11.2 (2010-02-02 10:50:14 CST)
starting pid 215, tty ”: ‘/etc/rc.sh’
** Mounting /etc/fstab
umount: proc: not mounted
umount: proc: not mounted
umount: /image.cfs: not mounted
umount: /image.cfs: not mounted
ln: /usr/sbin/system_init: File exists
Check MTD block device V2.06.12242009
MTD1 mount ok
mtd1 free size is 18432
MTD2 mount ok
mtd2 free size is 18432
** copy mtd1 files
cp: cannot stat ‘/sys/mtd1/firmwareupdate’: No such file or directory
cp: cannot stat ‘/sys/mtd1/hd_magic_num’: No such file or directory
cp: cannot stat ‘/sys/mtd1/upnp_serialnum.conf’: No such file or directory
cp: cannot stat ‘/sys/mtd1/MountError’: No such file or directory
cp: cannot stat ‘/sys/mtd1/mediaserver.udn’: No such file or directory
cp: cannot stat ‘/sys/mtd1/upnpav_portnumber’: No such file or directory
cp: cannot stat ‘/sys/mtd1/web_NToR1′: No such file or directory
cp: cannot stat ‘/sys/mtd1/dsk_mapping’: No such file or directory
rm: cannot remove ‘/sys/mtd1/udhcpd.leases’: No such file or directory
mv: cannot rename ‘/sys/mtd1/firmwareupdate’: No such file or directory
mv: cannot rename ‘/sys/mtd1/restore’: No such file or directory
mv: cannot rename ‘/sys/mtd1/format_ok’: No such file or directory
mv: cannot rename ‘/sys/mtd1/pls_sync’: No such file or directory
mv: cannot rename ‘/sys/mtd1/pls_chmod_a2′: No such file or directory
mv: cannot rename ‘/sys/mtd1/pls_chmod_b2′: No such file or directory
mv: cannot rename ‘/sys/mtd1/spare_dsk’: No such file or directory
mv: cannot rename ‘/sys/mtd1/std_raid1′: No such file or directory
mv: cannot rename ‘/sys/mtd1/old_prescan_version’: No such file or directory
cp: cannot stat ‘/sys/mtd1/ez-ipupdate.cache’: No such file or directory
cp: cannot stat ‘/sys/mtd1/ftpgroup’: No such file or directory
mv: cannot rename ‘/tmp/hd_magic_num’: No such file or directory
** link lib **
** link web **
** link /usr/bin **
** link /usr/sbin **
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
** link /usr/local/LPRng **
cp: cannot stat ‘/sys/crfs/default/server-key-nopassword.pem’: No such file or directory
mode: 16384
-o offset: 0
-f frequency: 0
maxerror: 16384000
esterror: 16384000
status: 64 (UNSYNC)
-p timeconstant: 2
precision: 1
tolerance: 33554432
-t tick: 9960
time.tv_sec: 1104988689
time.tv_usec: 394063
return value: 5 (clock not synchronized)
: getRTC time= 5/1/6 5:18:9

** set loopback interface
read mac from /dev/mtdblock4
MAC = 00:24:01:10:5F:3E
egiga0: mac address changed
** Activate Gigabit Interface
egiga0: link down
Stop fan
Set fan to low speed(2700)
egiga0: link up, full duplex, speed 100 Mbps
** execute rc.init.sh
route: SIOCADDRT: Network is unreachable
Setting hostname …. dlink-105F3E
Starting DHCP client ….
192.168.0.32
requested_ip=192.168.0.32
udhcpc (v1.11.2) started
Sending discover…
Sending discover…
Sending discover…
No lease, forking to background
hd verify v1.24.12222010
can not detect hd
Set Timezone=(GMT-08:00) Pacific Time(US & Canada); Tijuana
get IP = [NONE SET]
1.Set Date & time …(command: sntp -r ntp1.dlink.com &)
sntp: unable to locate IP address/number
sntp: Success
: getRTC time= 5/1/6 5:18:32
Jan 6 05:18:32 crond[640]: crond (busybox 1.11.2) started, log level 8

check button V2.77.02242011
1.10(1.82.0406.2011)
04/06/2011
mfg_search
create /tmp/fatmount script file
mount FAT storage devices
** Get MAC Addr
mount: /dev/sda is not a valid block device
mount: /dev/sdb is not a valid block device
mount: /dev/sdc is not a valid block device
Old BT binanry
does not exist directory
/usr/sbin/start_bt: line 20: ./btdog: not found
mount: /dev/sda1 is not a valid block device
mount: /dev/sdb1 is not a valid block device
mount: /dev/sdc1 is not a valid block device
/etc/shared_name: No such file or directory
Fan:Auto(Off/Low/High)
set fan speed to h
Set fan to high speed(7000)
format error
op_server 3 3 3 &
op_server v2.01.06012006
This may not a UPS device , please check it
sh: you need to specify whom to kill
posix_main begin
posix_main begin
Added user nobody.
starting pid 736, tty ”: ‘-/bin/sh’

BusyBox v1.11.2 (2010-02-02 10:50:14 CST) built-in shell (ash)
Enter ‘help’ for a list of built-in commands.

Detect 5182 chip
detect phy 1111
Jan 6 05:18:36 crond[745]: crond (busybox 1.11.2) started, log level 8

kill process
Jan 6 05:18:37 crond[768]: crond (busybox 1.11.2) started, log level 8

rm: cannot remove ‘/tmp/set_ddns_done’: No such file or directory
rm: cannot remove ‘/tmp/set_ddns_error’: No such file or directory
language=ENGLISH
usbcore: deregistering driver usblp
$Shutting down SMB services:
$Shutting down NMB services:
set fan speed to s
Stop fan
No found HD